|
Signal separators and translators
|
|
|
|
|
|
|
| SA1 |
Product description:
|
| SA1 device is a analog signal separator, destinated to galvanic separation of measure cirtuits (voltage or current). It converts any input signal to any output signal as 1:1 or other. It's task is to minimize interferencein measure circuits, and to fit two diferrent measure signals. Casing is 35 mm rail mountes. Power Supply 24VDC or AC. There is a complete galvanic separation of all circuits. |
|
| Technical parameters: |
| Power Supply | 21÷28 V/55 mA DC or AC |
| Secondary power supply for two-wire transducers |
24 V/50 mA |
| Measure signals for standard products | ▪ Input signals
0÷20 mA
4÷20 mA
0÷10 V
▪ Output signals
0÷20 mA
4÷20 mA
0÷10 V
|
| Basic error | ± 0,05 % MR |
|
|
|
|
|
|
|
|
|
|
|
| MT1-RS485 |
Product description:
|
| MT1-RS485 is a analog signal translator 4-20mA, 0-20mA, 0-10V to serial transmision in RS485 standard. It is destinated to work in multi-point system and is MODBUS RTU based. It can also be used in direct connection level probes PLH series or transducers PT series. Accurate class 0,1%. Transmission speed to 19200 bods. Casing is 35mm rail mounted. Power Supply 24VDC lub AC. All circuits are galvanic separated from each other. |
|
| Technical parameters: |
| Power supply | 21÷28 V/55 mA DC or AC |
| Input signal: | ▪ voltage 0÷10 V
▪ current 0÷20 mA, 4÷20 mA
▪ pressure series PT, PLH (option)
|
| Basic error | ± 0,05 % MR |
| Temperature stability | 0,01%/ºC |
| Comunication port | RS485 |
| Comunication protocol | MODBRUS RTU |
| Transmission speed | 2400, 4800, 9600 or 19200 bit/sek.
set by short circuit inside casing
|
| Transmission parameters | 8N1 (8 data bits, stop bit, no evenness) |
| Factory setting | address=1 speed=9600 bit/sec |
| Number of modules in one system |
typically 32 / max 254 |
| Separation | all circuits are galvanic separated from each other |
|
|
|
|
|
|
|
|
|
|
|
| SLT RS232-RS232 |
Product description:
|
| SLT RS232-RS232 is a separator, destinated to galvanic separation of transmission wires in RS232C standard. Transmission speed: max. 38400 bods. Casing is 35mm rail mounted. Power supply 24VDC or AC. All circuits are galvanic separated from each other. |
|
| Technical parameters: |
| Power supply | 21÷28 V/55 mA DC or AC |
| Transmission wiress length |
max 15 m |
| Transmission wires | Txd, Rxd, Cts, Rts,LED's on Rxd lines on both separator's sides |
| Transmission speed | max. 38400 bods |
| Separation | All circuits are galvanic separated from each other. |
| Isolation test voltage | 2 kV, 50 Hz, 1 min |
|
|
|
|
|
|
|
|
|
|
|
| SLT RS232-RS485 |
Product description:
|
| SLT RS232-RS485 is a separator-translator, destinated to convert RS232 signals to RS485 and back. Transmission kind: "half-duplex". Transmission speed: max. 19200 bods. Casing is 35 mm rail-mounted. Power supply 24VDC or AC. All circuits are galvanic separated from each other. |
|
| Technical parameters: |
| Power supply | 21÷28 V/55 mA DC or AC |
| Transmission wiress length | ▪ RS232 max 15 m
▪ RS485 max 1200 m
|
| Number of devices working in system RS485 |
max 32 |
| Transmission wires | ▪ RS232 Txd, Rxd, Rts, transmission
from RS232 side signalized by LED
▪ RS485 A, B, transmission from
RS485 side signalized by LED
|
| Transmission speed | max 115200 bods |
| Separation | All circuits are galvanic separated from each other |
|
|
|
|
|
|
|
|
|
|
|
| SLT RS232-RS422 |
Product description:
|
| SLT RS232-RS422 is a separaator-translator, destinate to convert RS232 signals to RS422 ones and back. Transmission kind: "full-duplex". Transmission speed: max. 38400 bods. Casing is 35mm rail mounted 35mm. Power supply 24VDC or AC. All circuits are separated from each other. |
|
| Technical parameters: |
| Power supply | 21÷28 V/55 mA DC or AC |
| Transmission wiress length | ▪ RS232 max 15 m
▪ RS422 max 1200 m
|
| Transmission wires | ▪ RS232 Txd, Rxd, Rts, transmission
from RS232 side signalized by LED
▪ RS422 Tx+(A), Tx-(B), Rx+(A),
Rx-(B), transmission from RS422 side
signalized by LED
|
| Transmission speed | max 38400 bods |
| Separation | All circuits are galvanic separated from each other |
| Isolation test voltage | 2kV, 50Hz, 1 min |
|
|
|
|
|
|
|
|
|
|
|
| SLT RS485-RS485 |
Product description:
|
| SLT RS485-RS485 is a separator, destinated to galvanic separation of transmission wires in RS485 and RS422 industry standards. Besides separation it can serve as amplifier-repeater wich enables lengthen transmission wires about 1200m and to attach more number of devices slave type. Transmission speed: max. 115000 bods. Casing is 35mm rail mounted. Power supply 24VDC or AC. All circuits are galvanic separated from each other. |
|
| Technical parameters: |
| Power supply | 21÷27 V/60 mA DC or AC |
| Transmission wiress length | max 1200 m |
| Number of devices working in one system RS485 |
max 32 |
| Transmission speed | max 115200 bods |
| Separation | all circuits are galvanic separated from each other |
| Operating temperature | 0÷60ºC |
|
|
|
|
|
|
|
|
|
|
|
| SLT RS232-TTY |
Product description:
|
| SLT RS232-TTY is a separator-translator, destinated to convert data transmited in RS232
to data transmited in TTY. Transmission speed: max. 115200 bods.
Casing is 35mm rail mounted. Power supply 24 VDC or AC.
All circuits are galvanically separated from each other. |
|
| Technical parameters: |
| Power supply | 21÷28 V/55 mA DC or AC |
| Transmission wires length | RS232 max 15 m
TTY max 1200 m |
| Transmission circuits | ▪ RS232 Txd, Rxd, according to RS232 standard,
transmission from RS232 side signalized by LED
▪ TTY Tx+, Tx-, Rx+, Rx-, current loop 20 mA,
transmission from TTY side signalized by LED
|
| Current loop parameters |
24 V/20 mA |
| Transmission speed | max 115200 bods |
|
|
|
|
Look at setting up instruction
|
|
|
|
|
|
|
|
|
Home
)
)
)
)
)
)
)
SA1